Differences

This shows you the differences between two versions of the page.

--- wio:wiopico-io16lnet-en [2026/01/07 12:24] – [WIO Address] rjversluis
+++ wio:wiopico-io16lnet-en [2026/01/09 08:18] (current) – rjversluis
@@ Line 18: / Line 18: @@
  \\
 =====GCA PCB====
-{{:gca:wio_loconet_01_v3_3d.png?300}} {{:gca:pict_01.png?300}}
+{{:gca:gca1001_3d.png?400|}} {{:gca:pict_01.png?300}}
-  * **[[:wio_loconet_01|WIOpicoLNet_01]]**\\
+  * **[[:GCA1001-en|:GCA1001]]**\\
  \\
@@ Line 29: / Line 29: @@
  \\
 =====WIO LNet setup=====
-If the WIOpicoLNet should be used as WiFi bridge the WiFi credentials must be set.\\
+If the WIOpicoLNet should be used as WiFi bridge the **[[:arduino:wio-setup-en#wlan|WLAN credentials]]** must be set.\\
-All other settings are under Configuretion.\\
+All other settings are under **[[:arduino:wio-setup-en#configuration|Configuration]]**.\\
 {{:wio:wiolnet-maintenance-en.png?600}}\\
 ====Options====
@@ Line 95: / Line 95: @@
 If the status pixel is used, pixel 1, the LED address is internally increased by one.\\
+ \\
+====Signals====
+LED signals can be defined in the same way as standard WIO.\\
  \\
@@ Line 101: / Line 105: @@
 Uses the binary TCP protocol __without echoing__ commands.\\
 :!: [[#options|Options7 "LAN Bridge" must be set.]]\\
+:!: [[#wio_lnet_setup|The WiFi credentials must be set.]]\\
 {{:wio:loconet-wiopicolnet-tcp-en.png?400}}\\
 ==== USB ====
@@ Line 114: / Line 119: @@
 ===== Tunnel packet =====
 To be able to use various WIO functions a tunnel packet is defined.\\
+==== 4 Data bytes ====
+^ OPC ^ Length ^ Destination ^  Operation  ^  Data  ^^^^^  CRC  ^
+|  0xEC  |  10  |  Node-ID  |  RASCII OPC  |  High bits 1  |  data 0  |  data 1  |  data 2  |  data 3  |  Checksum  | \\
 ==== 8 Data bytes ====
-^ OPC ^ Length ^ Destination ^  Operation  ^  Data  ^^^^^^^^^^ CRC ^
+^ OPC ^ Length ^ Destination ^  Operation  ^  Data  ^^^^^^^^^^  CRC  ^
-|  0xEC  |  15  |  Module#  |  RASCII command  |  High bits 1  |  data 0  |  data 1  |  data 2  |  data 3  |  High bits 2  |  data 4  |  data 5  |  data 6  |  data 7  |  Checksum  | \\
+|  0xEC  |  15  |  Node-ID  |  RASCII OPC  |  High bits 1  |  data 0  |  data 1  |  data 2  |  data 3  |  High bits 2  |  data 4  |  data 5  |  data 6  |  data 7  |  Checksum  | \\
-==== 4 Data bytes ====
-^ OPC ^ Length ^ Destination ^  Operation  ^  Data  ^^^^^ CRC ^
+==== 12 Data bytes ====
-|  0xEC  |  10  |  Module#  |  RASCII command  |  High bits 1  |  data 0  |  data 1  |  data 2  |  data 3  |  Checksum  | \\
+^ OPC ^ Length ^ Destination ^  Operation  ^  Data  ^^^^^^^^^^^^^^^  CRC  ^
+|  0xEC  |  20  |  Node-ID  |  RASCII OPC  |  High bits 1  |  data 0  |  data 1  |  data 2  |  data 3  |  High bits 2  |  data 4  |  data 5  |  data 6  |  data 7  |  High bits 3  |  data 8  |  data 9  |  data 10  |  data 11  |  Checksum  | \\
 ==== High bits ====
 |< >|
-^ # ^ High bits 1 ^ High bits 2 ^
+^ # ^ High bits 1 ^ High bits 2 ^ High bits 3 ^
-| 0 | data 0 | data 4 |
+| 0 | data 0 | data 4 | data 8 |
-| 1 | data 1 | data 5 |
+| 1 | data 1 | data 5 | data 9 |
-| 2 | data 2 | data 6 |
+| 2 | data 2 | data 6 | data 10 |
-| 3 | data 3 | data 7 |
+| 3 | data 3 | data 7 | data 11 |
-| 4 | nop | nop |
+| 4 | nop | nop | nop |
-| 5 | nop | nop |
+| 5 | nop | nop | nop |
-| 6 | Event flag | nop |
+| 6 | Event flag | nop | nop |
-| 7 |  -  |  -  |
+| 7 |  -  |  -  |  -  |
  \\