Differences

This shows you the differences between two versions of the page.

--- lnsv-en [2026/01/06 16:05] – rjversluis
+++ lnsv-en [2026/01/07 09:04] (current) – rjversluis
@@ Line 1: / Line 1: @@
-======LocoIO ======
+======LocoIO General======
 [[:english#rocgui_viewer|{{  :viewer.png}}]][[:english|{{  :rocrail-logo-35.png}}]]
 [[english|Content]] -> [[english#rocview|Rocview]] -> [[english#programming_dialogs|Programming]] -> **Stationary Decoders**\\
-   * **LocoIO**
+  * **[[lnsv-en|General]]** | [[locoio-addr-en|Query]] | [[loconet-easy-en|I/O]] | [[loconet-io-en|Port]] | [[locoio-opc-en|OPC]] |  [[locoio-multi-en|MultiPort I/O]] | [[locoio-servo-en|Servo]]
-     * **[[lnsv-en|General]]** | [[locoio-addr-en|Query]] | [[loconet-easy-en|I/O]] | [[loconet-io-en|Port]] | [[locoio-opc-en|OPC]] |  [[locoio-multi-en|MultiPort I/O]] | [[locoio-servo-en|Servo]]
 // \\ // \\
-{{locoio-gen-en.png}}\\
+{{locoio-gen-en.png?800}}\\
  \\
 ===== Module Address =====
-The module address is composed from the **Low** and **Sub** address and defaults to **81/1**. The range for both is 0-126.\\
+====Low====
+The module address is composed from the **Low** and **Sub** address and defaults to **81/1**. The range for both is 1-126.\\
 See also: __**[[:mgv50-en#configuring_gca50|GCA50 Configuration]]**__.\\
 __The address on the General Tab is used for all further Tabs.__\\
-\\
+====Sub====
 Low-Address + Sub-address can be out of the range from 1 to 126.\\
-This address can also be changed by double clicking on one off the [[locoio-addr-en|Adress List]] entries.\\
+This address can also be changed by double clicking on one off the [[locoio-addr-en|Query List]] entries.\\
 It is not possible to change the **Low** and **Sub** address at the same time; change them separately.\\
- \\
-===== Reset =====
+**Note:** //Sub-Address **70** is __reserved__ for **[[:wio:wiopico-io16lnet-en|WIOpicoLNet]]**.//\\
+ \\
+==== Reset ====
 With reset **all connected** LocoIO based module will be programmed with the address 81/1.\\
 This is only needed if the address is unknown or the module does not react on commands. Make sure only that module is connected to the LocoNet!\\
 A warning is shown if this action is selected: \\
 {{locoio-reset-warn-en.png}}\\
-Only the address registers are overwritten at this point. But if more than one units are listening to this address all further modifications will take place on all of them! So take care!
+Only the address registers are overwritten at this point. But if more than one units are listening to this address all further modifications will take place on all of them! So take care!\\
- \\
 As alternative all available addresses can be listed with the [[locoio-addr-en|Query]] button. For more details read the description of the address tab of this dialog.\\
  \\
+=====Setup=====
-=====LocoIO SV's=====
+ \\
+=====Registers=====
+ \\
+=====LocoIO SV Documentation=====
 The opcode OPC_PEER_XFER is used to exchange data between computer and decoder.\\
 Detailed SV information:\\
-  * http://www.locobuffer.com/LocoIO/SV_Tutorial.pdf
+  * {{:locoio:sv-tutorial.pdf|SV Programming Tutorial}} (EN)
-  * http://www.locobuffer.com/LocoIO/SV.pdf
+  * {{:locoio:locoio.pdf|LocoIO}} (EN)
-  * http://www.locobuffer.com/LocoIO/LocoIO.pdf
+  * {{:locoio:locoiosw.pdf|LocolO module software}} (NL)
  \\