Innovative Model Railroad Control System

User Tools

Site Tools

Trace:
lnsv-en

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
lnsv-en [2026/01/07 08:25] – rjversluislnsv-en [2026/01/07 09:04] (current) – rjversluis
Line 3: Line 3:
  
 [[english|Content]] -> [[english#rocview|Rocview]] -> [[english#programming_dialogs|Programming]] -> **Stationary Decoders**\\ [[english|Content]] -> [[english#rocview|Rocview]] -> [[english#programming_dialogs|Programming]] -> **Stationary Decoders**\\
-   * **LocoIO** +  * **[[lnsv-en|General]]** | [[locoio-addr-en|Query]] | [[loconet-easy-en|I/O]] | [[loconet-io-en|Port]] | [[locoio-opc-en|OPC]] |  [[locoio-multi-en|MultiPort I/O]] | [[locoio-servo-en|Servo]]
-     * **[[lnsv-en|General]]** | [[locoio-addr-en|Query]] | [[loconet-easy-en|I/O]] | [[loconet-io-en|Port]] | [[locoio-opc-en|OPC]] |  [[locoio-multi-en|MultiPort I/O]] | [[locoio-servo-en|Servo]]+
 // \\ // \\ // \\ // \\
    
Line 17: Line 16:
 See also: __**[[:mgv50-en#configuring_gca50|GCA50 Configuration]]**__.\\ See also: __**[[:mgv50-en#configuring_gca50|GCA50 Configuration]]**__.\\
 __The address on the General Tab is used for all further Tabs.__\\ __The address on the General Tab is used for all further Tabs.__\\
-\\+
 ====Sub==== ====Sub====
 Low-Address + Sub-address can be out of the range from 1 to 126.\\ Low-Address + Sub-address can be out of the range from 1 to 126.\\
Line 24: Line 23:
  
 **Note:** //Sub-Address **70** is __reserved__ for **[[:wio:wiopico-io16lnet-en|WIOpicoLNet]]**.//\\ **Note:** //Sub-Address **70** is __reserved__ for **[[:wio:wiopico-io16lnet-en|WIOpicoLNet]]**.//\\
- \\ 
  
-===== Reset =====+ \\ 
 +==== Reset ====
 With reset **all connected** LocoIO based module will be programmed with the address 81/1.\\ With reset **all connected** LocoIO based module will be programmed with the address 81/1.\\
 This is only needed if the address is unknown or the module does not react on commands. Make sure only that module is connected to the LocoNet!\\ This is only needed if the address is unknown or the module does not react on commands. Make sure only that module is connected to the LocoNet!\\
 A warning is shown if this action is selected: \\ A warning is shown if this action is selected: \\
 {{locoio-reset-warn-en.png}}\\ {{locoio-reset-warn-en.png}}\\
-Only the address registers are overwritten at this point. But if more than one units are listening to this address all further modifications will take place on all of them! So take care! +Only the address registers are overwritten at this point. But if more than one units are listening to this address all further modifications will take place on all of them! So take care!\\
- \\+
 As alternative all available addresses can be listed with the [[locoio-addr-en|Query]] button. For more details read the description of the address tab of this dialog.\\ As alternative all available addresses can be listed with the [[locoio-addr-en|Query]] button. For more details read the description of the address tab of this dialog.\\
 +
  \\  \\
 +=====Setup=====
  
-=====LocoIO SV's=====+ \\ 
 +=====Registers===== 
 + 
 + \\ 
 +=====LocoIO SV Documentation=====
 The opcode OPC_PEER_XFER is used to exchange data between computer and decoder.\\ The opcode OPC_PEER_XFER is used to exchange data between computer and decoder.\\
 Detailed SV information:\\ Detailed SV information:\\
lnsv-en.1767770705.txt.gz · Last modified: 2026/01/07 08:25 by rjversluis